Braun KF 185 Bedienungsanleitung PDF herunterladen (Seite 3)

Note: If the power supply is interrupted or the plug

is pulled out of the socket, the clock will run for a fur-

ther 15 minutes. All programmed function are also

stored for 15 minutes.

Filling with coffee grounds

Swing out the filter holder

(a) and insert the filter.

Put coffee grounds (not ground too finely) into the

filter and close the filter holder again (a) until it

snaps in place. Measure coffee according to the

strength desired.

Filling with water

Important: When filling with water and during coffee

preparation either the space compensator

or the

water filter cartridge

must be installed in the

water container

. Otherwise the water level indica-

tor

will not function correctly and the carafe may

overflow.

Fill the water container with as much cold water as

coffee is required. To do this, lift the cover for the

water container

and pour the cold water into the

water container

. The amount of water is shown on

the water level indicator

(maximum 12 cups –

125 ml each).

Space compensator

The space compensator

in the water container

takes up the space which is intended for the water

filter cartridge

. Unless the water filter cartridge is

installed in the water container, the space compen-

sator must always be inside the water container

when filling with water and brewing to avoid overfil-

ling. Keep the space compensator

as it has to be

installed in the water container if you have to decal-

cify your coffeemaker.

Water filter cartridge

The water filter cartridge

is suitable for drinking-

water only. It gives your purer tasting coffee by

removing chlrorine, bad tastes and odors as well as

scale. Provided the cartridge is regularly replaced,

it provides not only better tasting coffee, but also

can increase the life of your coffeemaker by prevent-

ing calcification.

Installing the water filter cartridge

Unpack the water filter cartridge

. Then put the fil-

ter cartridge for 10 minutes in a receptable filled with

water.

Remove the space compensator

from the water

container and replace it by the water filter cartridge

. Make sure to keep the space compensator

as it could be needed if you do not use the water filter

any longer at a future point in time or for

decalcification.

After having installed a new water filter cartridge,

allow the maximum amount of fresh, cold water to

run through the coffeemaker.

In order to ensure the proper functioning of the filter

cartridge, exchange it after 2 months of regularly

using the coffeemaker. In order to remind you to

replace the filter in time, you may set the dial

incorporated in the cover of the water container to

the month when the cartridge has to be exchanged.

Dial for water filter exchange

After having installed a new filter cartridge, set the

dial

2 months furhter by turning it from the reverse

side of the water container cover.

Pre-selecting the taste – AromaSelect dial

By adjusting the AromaSelect dial

, you can adjust

the taste of your coffee to suit your personal prefer-

ence – milder with less bitter aftertaste or stronger,

but always with the same full flavour. The Aroma-

Select dial

can be adjusted in two different ways,

both before you turn on the coffeemaker. With the

water container lid closed, grasp the dial by the two

raised grip points and turn in the desired direction.

Alternatively, with the water container lid open, turn

the dial with the attached L-shaped grip.

If you prefer milder coffee with less bitter aftertaste,

turn the AromaSelect dial

in the direction of the

symbol (b). Should you prefer a more stronger

taste, turn the AromaSelect dial towards the

symbol. Regardless of the position you select, the

coffee will always have the same full coffee flavour

only a milder or stronger aftertaste. With the cover

of the water container closed, the selected setting

can always be seen (c).

Manual operation

To switch on, press the «on/off» button

The control lamp

will light up red indicating that

the coffeemaker is switched on and brewing is in

process. To switch off the coffeemaker, press the

«on/off» button

. The red control lamp

will

briefly flash and all control lamps will go off.

Automatic operation

To programme the automatic operation, press the

«automatic» button

until the green control lamp

begins to flash. Three noughts or the previously pro-

grammed time appear on the display

When the green control lamp

begins to flash,

release the button

and, as described under

«Setting the clock», programme the time for

automatic operation by pressing the buttons «h»

and «min»

. After programming is completed, the

green control lamp

will go off after 5 seconds.

To activate automatic operation, briefly press the

button «automatic»

. The green control lamp

lights up, the pre-set brewing, time is briefly shown

on the display

. Brewing automatically begins at

the pre-set time.

When the brewing process begins, the green control

lamp

goes off and the control lamp

lights up red

to indicate that brewing has begun.

If, for instance, you want to make coffee at the same

time on the following day, you must activate the

automatic operation again (see above). However,

this should only be done after brewing is finished or

the programmed time for the hotplate switch-off

(when none of the control lamps are on), as you

could otherwise interrupt brewing or switch off the

hotplate

Making coffee

Place the carafe with the lid on onto the hotplate

and snap the filter holder

in place. Switch the

coffeemaker on as described. Brewing time is

approx. 50 seconds per cup (including dripping).

A «drip stop» prevents dripping when lifting off the

Carafe shortly

. Remove the filter holder

to empty

grounds (see section «Cleaning»).

Brewing small amounts

(1-3 cups – 125 ml each)

Switch the coffeemaker on with the «on/off» button

. The control lamp

lights up red.

Press the button «1-3 »

. The yellow control

lamp

lights up.

This indicates that the function for brewing small

amounts is activated and the coffeemaker is in

operation. Brewing will begin.

The facility for brewing small amounts can be pre-set

in the automatic operation mode. Press briefly the

«automatic» button

. The control lamp

lights up

green. Then press the button «1-3 »

and the

yellow control lamp

ligts up.

The coffeemaker will only brew small amounts of

coffee in this mode if both the «1-3 cups» facility

and the timing are pre-set.

This function can be switched on or off during the

brewing process. To switch off the function for small

amounts, press the button «1-3 »

. The yellow

control lamp

will go off.

Audio-visual «coffee ready» signal

The signal indicates that brewing is finished and the

water has run through the filter. The coffeemaker

beeps 5 times and the control lamp

changes from

red to green. To switch off the coffeemaker

manually, press the «on/off» button

. The control

lamp

lights up red briefly and all control lamps

then go off.

Ajustable heating temperature

The heating temperature can be adjusted approxi-

mately 5 °C using the knob «–temp.+»

. To reduce

the temperature, turn the knob anti-clockwise. To

increase the temperature, turn the knob clockwise.

Keeping the coffee hot

The carafe can remain on the hotplate

which

begins to heat up when the coffeemaker is switched

on and will keep the coffee hot until the coffeemaker

is switched off (red control lamp goes out).

Automatic hotplate switch-off

The temperature sensor

in the hotplate

regu-

lates the temperature of the coffee irrespective of

the amount in the jug. The coffeemaker can be set

to stay hot after brewing for up to 4 hours. Press

the «on/off» button

until the control lamp

begins to flash red and the heating time appears on

the display

. Release the «on/off» button t and

set the desired heating time with the buttons «h»

and «min»

o from 3 hours 59 minutes to 0 hour 00

minutes. When the control lamp

u shining red goes

off, the pre-set heating time is stored in the memory

and the display shows the time of day again.

After the brewing process, the control lamp

u lights

up green until the coffeemaker is automatically

switched off at the end of the heating time. A double

beep can be heard and all control lamps go off.

Cleaning

Always pull the plug out of the socket before clean-

ing (all programmed functions are stored for approxi-

mately 15 minutes). The appliance should never be

immersed into water. Swing out the filter holder

and pull it off upwards from the filter support bracket

7 (e). To replace, set the curved protruding rim of

the filter holder

8 on top of support bracket 7. Be

sure that the rib under the rim of the filter holder

fits snugly into the groove on the support bracket

so that the filter holder

8 fits nearly into place and

so the filter holder closes easily into the machine.

To wash, take the lid off the carafe (d). The carafe,

lid

and filter holder can be cleaned in the dishwasher

All other parts should be cleaned will a damp cloth

only. After cleaning, put the lid back on the carafe

(d). Clean the hotplate

9 with liquid cleansers only.

Do not use abrasive cleansers. The filter support

bracket

7 can be taken off for cleaning. Swing it out,

push it up and pull it off diagonally downwards (f).

To replace, insert the top first.

1 2 3 4

AromaSelect 1

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun KF 185 Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kaffeemacher Braun KF 185