Braun G 1300 Bedienerhandbuch PDF herunterladen (Seite 5)

English

Our products are engineered to meet the highest

standards of quality, functionality and design.

We hope you thoroughly enjoy your new Braun

appliance.

Caution

Read all instructions carefully before using this

product.

•

This appliance was constructed to process normal

household quantities.

•

This appliance is not intended for use by children or

persons with reduced physical or mental capabilities,

unless they are given supervision by a person

responsible for their safety. In general, we recommend

that you keep the appliance out of reach of children.

•

Before operating, check whether your voltage

corresponds to the voltage printed on the unit.

•

The motor unit

must not be held under running

water, plunged into water, or operated on wet

surfaces.

•

Do not allow the motor unit to become wet,

especially when processing moist food (if it does,

pull the plug out of the socket and clean the

motor unit – see «Cleaning»).

•

Braun electric appliances meet applicable safety

standards.

•

This appliance can only be opened by an author-

ised Braun Service Centre for repairs.

•

Faulty, unqualified repair work may cause acci-

dents or injury to the user.

Description

Cap

Disc

Notch in the disc

Blade (stainless steel)

Worm

5 Grinder head with filling shaft

E Protrusion in the metal housing 5

Feeder tray

7 Pusher

8 On/off switch

9 Motor unit

j Cord storage

«Kubbe» attachment (only G 1500 model)

l Sausage filler (only G 1500 model)

Disc

3 discs household size 5 (hole diameters 3 mm,

4.5 mm, 8 mm).

«Kubbe» attachment / Sausage filler

These attachments can be inserted instead of the disc

2 and the blade 3.

Safety fuse

If the motor switch is turned on, but the motor sud-

denly stops or does not run, the built in safety fuse

has been activated. Should this happen, turn the

switch off until the motor has cooled off (approxi-

mately 15 minutes).

If the motor will not start when switching it on again,

repeat the cooling off procedure (see above).

Put away the unit after use only after you have turned

the motor off and disconnected the plug.

Before using

All parts of the grinder attachment were covered with a

lubricating film before leaving the factory. They must be

washed before using the first time (see «Cleaning»).

Assembly

– Please note the correct assembly order of

parts

1 -5.

– The sharp side of the blade

3 must face the disc 2.

– Guide the notch

B in the disc 2 over the protrusion

E in the grinder head 5.

– After assembling the parts

2 -4, screw the cap 1

moderately tight onto the grinder head

The assembled grinder head

5 is joined to the motor

unit

9 with a bayonet lock. Insert the metal housing into

the motor unit by holding the filling shaft of the grinder

head at an angle of 45° clockwise (the level arrow on

the grinder head must coincide with the arrow on the

motor unit) (A). Turn the grinder head anti-clockwise in

the direction of the upright arrow (A) until the filling shaft

snaps into place in an upright position (B). Place the

feeder tray

6 on the filling shaft.

Operating

Turn the motor on before filling in meat, fish, vegeta-

bles, etc. To do so, press the switch

8 and let it latch.

To turn the unit off, unlatch the switch by pressing

lightly.

Before processing meat, remove tendons and bones

and cut it into strips. Besides meat, the machine will

also process fish, vegetables, onions, soaked bread

rolls, boiled potatoes, stoned plums for jam. Fill the

prepared meat or vegetables into the feeder tray

6 and

push it down into the filling shaft with the pusher

Never use a fork, a spoon handle or a similar object. If

meat is crushed instead of being cut properly, please

check

whether the meat grinder is assembled correctly

(e. g.

whether you have perhaps over-looked inserting

one of the parts) or clean the blade

3 and disc 2.

Notice: When processing food with high power con-

sumption – e. g. sunflower seeds mixed with oats at a

ratio of 1:3 (approximately 800 W) – do not exceed an

operating time of 10 seconds.

Before using the «Kubbe» attachment / Sausage

filler

l, the meat has to be ground twice.

Cleaning

Wipe the motor unit

9 with a damp cloth only and wipe

it dry. All other parts can be washed in hot water with

normal dishwashing liquids. The disc

2 should be

wiped dry. Do not clean in the dishwasher.

Storage

There is a practical cord storage

j at the base of the

unit (C).

Subject to change without notice.

This product conforms to the European

Directives EMC 2004/108/EC and Low

Voltage 2006/95/EC.

Please do not dispose of the product in the

household waste at the end of its useful life.

Disposal can take place at a Braun Service

Centre or at appropriate collection points

provided in your country.

4195357_S4_38 Seite 5 Donnerstag, 19. Juli 2007 11:04 11

1 2 3 4 5 6 7 8 9 10 ... 37 38

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun G 1300 Bedienerhandbuch Seite 5

Kommentare zu diesen Handbüchern