Braun Personal Lift 403 Bedienungsanleitung PDF herunterladen (Seite 3)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 34274 Rev. A

Main Lift

Wiring

Harnesses

Strobe

Alarm

Platform Lights

Threshold Mat 1

Main Lift Wiring

Harnesses

Threshold Mat 2

MCI Door Operator

MCI Full Closed

To Lift

1

Disconnect

and remove

eye terminal

2

Connect vehicle

interlock signal wires

To Vehicle Inte

rl

o

c

k

V

ehicle Secure Signal

To J

umper #3

1730A

Power Switch

3

Electrical, Hydraulic and Interlock

Note:

Remove

plug from

vent tube.

Connect red positive

(+) power cable here

(from Circuit Sentry).

Chassis

5/16"

External Tooth

Star Washer

9/32"

Diameter

Pilot Hole

Thread

Cutting

Screw

Figure J

Ground Cable Mounting

Pump Ground Cable:

One ground cable is pump mount-

ed. Connect cable to a vehicle

framing member (see Figure J).

Vehicle Battery Ground Cable:

A ground cable (minimum 2 gauge)

must be connected from vehicle

battery negative post to the same

vehicle framing member the pump

ground cable is attached to.

Ground Cable Corrosion:

When mounting ground

cables, remove undercoat-

ing, dirt, rust, etc. from

framing member around

mounting holes. Apply

protective coating to mount-

ing holes to prevent corro-

sion. Failure to do so will

void warranty of certain

electrical components.

Pump Module Mounting

Mount the pump module

case to the inner wall

of the adjacent storage

compartment as shown

in Figure I.

Check for obstructions

before drilling, cut-

ting holes or installing

mounting hardware.

Note: Locate and drill

hydraulic hose, wiring

harness and manual

release cable access

holes before mounting

pump. A 3" diameter

plastic grommet may be

used (supplied).

Figure L

Note: All

wiring harness

connections

must be in-

side the pump

module box.

Vehicle and Lift Interlocks

The pump module is

equipped with a lift interface

9-circuit connector (female

socket). A mating 9-circuit

connector (male plug) is

supplied. To meet mini-

mum NHTSA requirements,

connect to vehicle interlock

harness as outlined in

Figure L (Steps 1-4).

Power Cable

Aux.

Bat.

Pos.

Neg.

1/8" x 4" x 4"

Plastic

12"

Max.

Circuit

Sentry

Lead

Cable

Hydraulics:

Remove the plug

from 1/4" diameter

clear vent tube.

See Figure L.

Route hydraulic

hose assembly

through compart-

ment wall to quick-

disconnect fitting at

lift. Connect hose.

Circuit Sentry:

Install Circuit

Sentry as shown

in Figure K. At-

tach power cable

and lead cable as

detailed.

Figure K

Calibration and

Floor Level

Adjustment

Following electri-

cal, hyrdaulic

and interlock

installation, check

calibration and

floor level adjust-

ments as defined

in Panel 4.

Pump

Mounting

Bracket

Figure I

Adjacent

Compartment

Wall

1/4-20 x 3/4"

Hex Bolts

(Typical)

3/8"-16 x 1" Hex Bolts with Flat

Washer and Nylock

®

Hex Nuts

Beeper/Strobe

Alarm and Plat-

form Lights:

Connect har-

nesses to mating

harnesses at

pump module.

Housing/Carriage

Harnesses:

Route two main wir-

ing harnesses from

lift to pump module.

Connect to mating

harnesses at pump.

Threshold Warning Sensor:

Connect both threshold sen-

sor mat harnesses to mating

Y-harness at pump module

(labeled). Both mats must

be installed on a flat rigid

surface.

Inboard edge of inboard

mat must be minimum 18"

from edge of finished floor

or stepwell.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare