Braun Personal Lift 403 Bedienungsanleitung PDF herunterladen (Seite 4)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 34274 Rev. A

MP916

0.010Ω

.5% R

321

LCD MODULE

8.00M

L_DN

B_UP

L_OUT

L_UP

B_DN

L_IN

50# CAL

O_BAR

D14

J27 U?

CYCLE

DIAG

U15

U11

U10

J11

J10

J17

J16

J14

J21J19

J20

D13

D11

83J93J

K7K10

D12

D10

100

VHA

C12

220

CFK

C18

100

VHA

C13

MAG_SW

HAND-1

HAND-2

INT

D/S

U/D

J29

J30

J22

J25

10 9 8 7 6

SVC LIGHT

32J4

R55

8.00M

R54

R57

R60

R61

R52

R42

Lift_Out Floor_SW

R41

R40

R39

R27

R77

R53

R68

C10

C17

C14

C11

J37

JIHG

4 3 2 1

RL11

220

35A

220

35A

B - UP

B - DN

L - OUT

L - IN

100419-001 REV

GND

PWR

LIGHTS

ALARM VALVE PUMP

R31

R30

R21

R32

R34

R33

R35

R46

R58

R49

R51

R44

R36

R47

R45

R37

R70

R72

R26

R75

R29

R76

J35

54J74J

J15

C23

C19

R64

R62

R78

R48

R69

D16 D17

J13

SW_1 SW_0

J36

J32

MAT

J40

U20

FL_CL

Bit_1

Bit_0

50# CAL

O_BAR

U11

K7K10

220

CFK

6C9

C18

C17

V104

R32

1001

R34

1001

R33

1001

R35

1001

R26

2400

R29

2051

FL_CL

Bit_1

Bit_0

The outer barrier will not raise if occupied.

A visual and audible warning will activate if the

threshold area is occupied when the platform is at

least one inch below floor level.

Platform movement is prohibited beyond the posi-

tion where the inner roll stop is fully deployed (up).

Lift platform movement shall be interrupted unless

the outer barrier is deployed (up).

Vehicle movement is prevented unless the lift door

is closed, ensuring the lift is stowed.

Lift operation shall be prevented unless the

vehicle is stopped and vehicle movement is

prevented.

The platform will not fold/stow if occupied.

The inner roll stop will not raise if occupied.

Verify platform lighting when lift is deployed and

pendant illumination when lift is powered.

Floor Level Switch

The Floor Level switch stops upward travel of the platform

during the Up function (activated by the torque tube-mounted

Floor Level cam). Position the lift platform 1" above floor

level using the manual operation system (detailed on

opposite side of this sheet). Loosen the clamp securing the

torque tube-mounted Floor Level cam. Rotate the cam until

the Floor Level switch is activated (cam depresses switch).

Note: Check the floor level position of the platform and the

inner roll stop after powering the pump. Hydraulic pressure

may affect platform height slightly. Fine tuning adjustment

(tweaking) of the Floor Level switch may be required.

The inner roll stop must rest properly on the vehicle floor

when the lift is deployed. Adjust the inner roll stop only if

necessary (refer to the service manual).

Calibration and Floor Level Adjustment

Floor Level Switch

Floor Level Cam

Torque Tube

Cam depressing switch.

FMVSS 403/404 Certiﬁcation Checklist

The operations listed below must be functionally verified.

Platform Sense Calibration

1. There must be no weight on platform.

2. Press hand-held pendant UP switch to raise platform a minimum

3" above stow level.

3. Press and hold control board 50# CAL. button. While pressing

the 50# CAL. button, press and hold the hand-held pendant

STOW switch (button). The platform will lower to stow level

(begin stow function), and then start to raise. Release 50#

CAL. button immediately when platform starts to raise from stow

level.

4. After calibration, the LCD screen should read “PF OCCUPIED”

whenever there is 50 lbs. or more present on the platform. The

50 pound platform sensing is now calibrated.

Ground Sense Calibration

1. Press hand-held pendant DOWN switch to lower platform fully to

ground level.

2. While continuing to press the pendant DOWN switch, press and

then release the control board O_BAR GND. button.

3. Release the pendant DOWN switch.Ground level sensing is now

calibrated.

Outer Barrier Occupied Calibration

1. Press hand-held pendant DOWN switch to lower platform fully to

ground level.

2. Once outer barrier is fully unfolded (ramp position), release the

pendant DOWN switch.

3. Press and hold the control board O_BAR GND. button. While

holding O_BAR GND. button, press hand-held pendant UP

switch to raise the outer barrier. Be sure to release O_BAR

GND. button when outer barrier reaches approximately half full

up (vertical) position.

4. After calibration, the LCD screen should read “OUT-BAR OCCU-

PIED” whenever there is weight present on the outer barrier.

NUVL855RM24 Control Board

50# CAL

Button

O_BAR GROUND

LVL Button

34274 Rev. A

Dual

Outer Barrier

Threshold

Area

Platform

Lighting

Visual and Audible

Threshold Warning

Platform

Inner

Roll Stop

DOT — Public Use Lift

Public use vehicle manufacturers

are responsible for complying with

the lift lighting requirements in Fed-

eral Motor Vehicle Safety Standard

No. 404, Platform Lift Installation in

Motor Vehicles (49 CFR 571.404).

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun Personal Lift 403 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern