Braun 403 Bedienungsanleitung PDF herunterladen (Seite 7)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494

Maintenance and Lubrication

Speciﬁed (recommended) Available Braun

Lubricant Type Lubricant Amount Part No.

LO - Light Oil

LG - Light Grease

Light Grease Lubriplate 14 oz.

(Multipurpose) Can

Light Penetrating Oil LPS2, General Purpose 11 oz.

(30 weight or equivalent) Penetrating Oil Aerosol Can

Stainless Stick Door-Ease 1.68 oz.

Style (tube) Stick (tube)

DE - Door-Ease

15807

15806

15805

See the Maintenance/Lubrication Schedule for recommended applications per number of cycles.

Lubrication Diagram

Platform

Outboard

Platform

Inboard

Parallel Arm

Pivot Pins (8)

Lift-Tite Latch Dampening

Spring (2 springs - 4 Points)

Parallel Arm

Pivot Pins (8)

Inboard Locator

Pivot Points

Platform Pivot Pin (2 Points)

Platform Fold Axles (2)

UHMW Bearing (4)

Rotating Pivot

Slide Arm Pivot Pins

Switch Arm Pivot Pins (2)

Lift-Tite Latches

(Tower Pivot Points - 2)

Platform Fold Link Roller/Pin (4)

Outer Barrier Hinge Pivot Points

(2) and

Outboard Platform Pivot Pins (2)

Outer Platform Pivot Pins (2)

Outer Barrier Activation

Foot Pivot Point (2)

Outer Barrier

Arm Slots (2)

Maintenance and

lubrication procedures

must be performed as

speciﬁed by an autho-

rized service techni-

cian. Failure to do so

may result in serious

bodily injury and/or

property damage.

RNING

Maintenance and Lubrication Schedule

Proper maintenance is necessary to ensure safe,

troublefree operation. Inspecting the lift for any

wear, damage or other abnormal conditions should

be a part of a regular service program. Simple

inspections can detect potential problems.

The maintenance and lubrication procedures speci-

ﬁed in this schedule must be performed by a Braun

authorized service representative at the scheduled

intervals according to the number of cycles.

Braun dual parallel arm lifts are equipped with hard-

ened pins and self-lubricating bushings to decrease

wear, provide smooth operation and extend the

service life of the lift.

When servicing the lift at the recommended inter-

vals, inspection and lubrication procedures speciﬁed

in the previous sections should be repeated. Clean

the components and the surrounding area before

applying lubricants. LPS2 General Purpose

Penetrating Oil is recommended where Light Oil is

called out. Use of improper lubricants can attract

dirt or other contaminants which could result in wear

or damage to the components. Platform compo-

nents exposed to contaminants when lowered to the

ground may require extra attention.

Lift components requiring grease are lubricated dur-

ing assembly procedures. When these components

are replaced, grease must be applied during instal-

lation procedures. Speciﬁed lubricants are available

from The Braun Corporation (part numbers provided

above).

All listed inspection, lubrication and maintenance

procedures should be repeated at “750 cycle”

intervals following the

scheduled “4500 Cycles”

maintenance. These

intervals are a general

guideline for scheduling

maintenance procedures

and will vary according

to lift use and conditions.

Lifts exposed to severe

conditions (weather, envi-

ronment, contamination,

heavy usage, etc.) may

require inspection and

maintenance procedures

to be performed more

often than speciﬁed.

Maintenance Indicator: The Lift Ready green LED

mounted on top of the pump cover will begin to blink

after every 750 cycles. The blinking LED will not affect

the functions of the lift, but is a reminder to complete

necessary maintenance and lubrication.

Once the lift has been serviced, fully stow the lift. Once

stowed, press the UP button on the hand pendant and

the Floor Level Set button on the back side of the pump

cover until the Lift Ready green LED stops blinking.

Discontinue lift use immediately if maintenance

and lubrication procedures are not properly performed,

or if there is any sign of wear, damage or improper

operation. Contact your sales representative or call

The Braun Corporation at 1-800-THE LIFT. One of our

national Product Support representatives will direct you

to an authorized service technician who will inspect

your lift.

Outer barrier hinge pivot points (2)

Outer barrier arm slots (2)

Outboard platform pivot pins (2)

Outer barrier activation foot pivot pins (2)

Platform fold link rollers and pins (4 sets)

Outer platform pivot pins (2)

Lift-Tite

™

latches (tower pivot points - 2)

Lift-Tite

™

latch gas (dampening) spring pivot

points (2 springs - 4 points)

Inspect Lift-Tite

™

latches and gas springs for wear

or damage (bent, deformed or misaligned), posi-

tive securement (external snap rings) and proper

operation

Apply Light Oil - See Lubrication Diagram

Resecure, replace defective parts or otherwise

correct as needed. Note: Apply Light Grease to

Lift-Tite

™

latch tower pivot point if replacing latch.

750

Cycles

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun 403 Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Braun 403