Braun Personal Lift Corporation FMVSS No. 403 Bedienungsanleitung PDF herunterladen (Seite 5)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32553 Rev. A

Lift Operating Instructions

Control Switch Functions:

folding handrails and a dual

outer barrier system.

Before lift operation, park the

vehicle on a level surface, away

from vehicular trafﬁc. Place the

vehicle transmission in “Park”

and engage the parking brake.

Open manual doors fully, being

certain the doors are secured in

the fully open position.

It is the responsibility of the lift

operator (attendant) to prop-

erly open, secure and close the

vehicle lift doors, to activate any

auxiliary interlock (if equipped),

to load and unload the wheel-

chair passenger (or standee) on

and off the lift platform, and to

properly activate all lift functions.

In event of power or equipment

failure, refer to the Manual Oper-

ating Instructions section.

RNING

Whenever a

passenger is on the

platform, the:

• Passenger must

be positioned

fully inside yellow

boundaries

• Wheelchair brakes

must be locked

• Inner roll stop and

outer barrier must

be up.

Failure to do so may

result in serious

bodily injury and/or

property damage.

DOOR STOW

DOWN UP

Note: The instructions out-

lined here are applicable for

“Public-Use” NUVL lift mod-

els equipped with dual

OPEN DOOR(S) AND SECURE

Manually open door(s) fully and

secure.

TO DEPLOY PLATFORM:

1. Stand clear and press the UP

switch until the platform extends

fully. Release switch.

2. Pull handrail detent pins, lift

handrails up to vertical position and

reinsert detent pins.

3. Lift outer barrier to vertical position.

4. Press the UP switch until the plat-

form stops (raises to ﬂoor level)

and inner roll stop unfolds to ﬂoor

level. Release switch.

TO UNLOAD PASSENGER:

1. Read Note below! Load pas-

senger onto platform and lock

wheelchair brakes.

Note: Passenger must be

positioned fully inside yellow

boundaries and outer barrier must

be UP.

2. Press DOWN switch until the entire

platform reaches ground level and

the outer barrier unfolds fully

(ramp position). Release switch.

3. Unlock wheelchair brakes and

unload passenger from platform.

Note: Outer barrier must be fully

unfolded (ramp position) until the

entire wheelchair (or standee) has

crossed the outer barrier.

UP: From the stowed position, pressing the UP

switch deploys (extends) the platform fully. Release

the UP switch once the platform has extended fully

in order to deploy the outer barrier and handrails.

The platform will continue to raise to ﬂoor level if the

UP switch is not released and handrail procedures

may be more difﬁcult (ﬂoor level height varies per

vehicle). Pull the handrail detent pins and lift the

handrails to the vertical position. Reinsert the de-

tent pins after the handrails are raised. Lift the outer

barrier to the vertical position. Press the UP switch

until the platform stops (raises to ﬂoor level), and the

inner roll stop unfolds to ﬂoor level.

From ground level, the UP function will ﬁrst au-

tomatically raise (rotate) the outer barriers to the

upright (vertical) position. The platform then raises

to ﬂoor level position. Note: The lift will not raise

if the outer barrier is not in the UP position (built-in

safety feature).

DOWN: The DOWN function lowers the platform

to ground level and then unfolds the outer barriers

to the ramp (horizontal) position. From the stowed

position, the lift will extend fully and then lower.

STOW: The STOW function raises or lowers the

platform to stow level and then moves the platform

inward (retracts) to the stow position. Handrails

and Outer Barrier: The tall outer barrier and the

handrails must be folded down to the platform

(horizontal) position before stowing (retracting)

the platform. The handrail detent pins must be re-

inserted before stowing the platform also. Note:

The lift will not stow with weight on the platform

(built-in safety feature).

DOOR CLOSE: This function is not applicable

for “Public-Use” NUVL lift models (manual door

system and attendant operated lift).

Note: If any of these functions do not occur as

described, discontinue lift use immediately and

contact your sales representative or call The

Braun Corporation at 1-800-THE LIFT

. One of

our national Product Support representatives will

direct you to an authorized service repairman who

will inspect your lift.

Handrails and Dual Outer Barrier:

The folding handrails and tall outer

barrier are manually operated. The

spring-loaded outer barrier (tall barrier)

and the handrails rest on the platform

when the lift is not in use. The outer

barrier must be raised to the vertical

position and the handrails must be

lifted to the vertical position whenever

a passenger is on the platform.

The tall outer barrier and the handrails

must be folded down to the platform

(horizontal) position before stowing

the lift. The handrails fold down onto

the outer barrier to secure the barrier

in the horizontal position.

Each handrail is secured with two de-

tent pins (one pin at the base of each

vertical support tube). The detent pins

must be removed before the handrails

can be folded or unfolded and the

detent pins must be reinserted after

folding or unfolding the handrails.

TO LOAD PASSENGER:

1. Read Notes below! Load pas-

senger onto platform and lock

wheelchair brakes.

Note: Outer barrier must be fully

unfolded (ramp position) until the

entire wheelchair (or standee) has

crossed the outer barrier.

Note: Passenger must be

positioned fully inside yellow

boundaries.

2. Press UP switch to fold outer bar-

rier UP fully (vertical), raise the

platform to ﬂoor level and unfold

inner roll stop to ﬂoor level. Re-

lease switch.

3. Unlock wheelchair brakes and

unload passenger from platform.

TO STOW PLATFORM:

1. Fold outer barrier down to platform

(horizontal) position.

2. Pull handrail detent pins, fold hand-

rails down to platform (horizontal)

position and reinsert detent pins.

3. Press STOW switch until platform

stops (retracts fully). Release

switch.

CLOSE DOOR(S)

Manually close door(s) fully.

Hand-held Pendant Control:

The hand-held attendent's pendant control is

equipped with four push button switches (DOOR,

STOW, DOWN and UP). The momentary switches

activate the automatic lift functions. Simply press

the switch labeled for the intended function.

When there is power to the lift, the lift function labels

illuminate to identify the functions.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun Personal Lift Corporation FMVSS No. 403 Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Braun Personal Lift Corporation FMVSS No. 403