Braun Door 33657 Bedienungsanleitung PDF herunterladen (Seite 4)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 33675 Rev. A

Threshold

Sensor Mat

FMVSS 403/404 Certiﬁcation Checklist

Dual

Outer Barrier

Threshold

Area

Platform

Lighting

Visual and Audible

Threshold Warning

Platform

Inner

Roll Stop

DOT — Public Use Lift

Public use vehicle manufacturers

are responsible for complying with

the lift lighting requirements in Fed-

eral Motor Vehicle Safety Standard

No. 404, Platform Lift Installation in

Motor Vehicles (49 CFR 571.404).

Floor Level Switch

The Floor Level switch stops upward travel of the platform

during the Up function (activated by the torque tube-mounted

Floor Level cam). Position the lift platform 1" above �oor

level using the manual operation system (detailed on

opposite side of this sheet). Loosen the clamp securing the

torque tube-mounted Floor Level cam. Rotate the cam until

the Floor Level switch is activated (cam depresses switch).

Note: Check the �oor level position of the platform and the

inner roll stop after powering the pump. Hydraulic pressure

may affect platform height slightly. Fine tuning adjustment

(tweaking) of the Floor Level switch may be required.

The inner roll stop must rest properly on the vehicle �oor

when the lift is deployed. Adjust the inner roll stop only if

necessary (refer to the service manual).

Calibration and Floor Level Adjustment

Floor Level Switch

Floor Level Cam

Torque Tube

Cam depressing switch.

Platform Sense Calibration

1. There must be no weight on platform.

2. Press hand-held pendant UP switch to raise platform a minimum

3" above stow level.

3. Press and hold control board 50# CAL. button. While pressing

the 50# CAL. button, press and hold the hand-held pendant

STOW switch (button). The platform will lower to stow level

(begin stow function), and then start to raise. Release 50# CAL.

button immediately when platform starts to raise from stow level.

4. After calibration, the LCD screen should read “PF OCCUPIED”

whenever there is 50 lbs. or more present on the platform. The

50 pound platform sensing is now calibrated.

Ground Sense Calibration

1. Press hand-held pendant DOWN switch to lower platform fully to

ground level.

2. While continuing to press the pendant DOWN switch, press and

then release the control board O_BAR GND. button.

3. Release the pendant DOWN switch.Ground level sensing is now

calibrated.

Outer Barrier Occupied Calibration

1. Press hand-held pendant DOWN switch to lower platform fully to

ground level.

2. Once outer barrier is fully unfolded (ramp position), release the

pendant DOWN switch.

3. Press and hold the control board O_BAR GND. button. While

holding O_BAR GND. button, press hand-held pendant UP

switch to raise the outer barrier. Be sure to release O_BAR

GND. button when outer barrier reaches approximately half full

up (vertical) position.

4. After calibration, the LCD screen should read “OUT-BAR OCCU-

PIED” whenever there is weight present on the outer barrier.

NUVL Control Board 31414A-NS

103

102

103

102

103

102

103

102

220

CHA

220

CHA

100

VHA

220

35A

3 2 1

102

LCD MODULE

106 E

330

8.00M

MP916

0.010Ω

.5% R

D7 D8

D5 D6 D3 D4

D2 D1

C20

R15

R14

L_DN

B_UP

L_OUT

L_UP

B_DN

L_IN

SW1

SW2

50# CAL

O_BAR

GROUND LVL

R10

C11

C10

R42

R32

C21

ZD3

R27

R29

R31

cycle

diag

CLOSECLOSE

OPEN

D10D11

U17

R37

R36

C15

R33

R11

C22

D13

U18

C14

U12

B LIGHT A

Magnetic

Remote

U21

HAND-1

HAND-2

INLK-1

D/S

U/D

R28

D26

D25

D24

D23

R26

R16

U15

U14

R13

R20 R19

R18

U16

R39

Lift Devices

4 3 2 1

Door

Operator

RL11

RL10

IN L H

MAT

C16

220

35A

U20

R25

C12

D12

VR3

FS1

U19

RL9

R34

C13

FS2

FS8

VR1

VR2

LIGHT

ALARM

PUMP

VALVE

L_IN

L_OUT

B_UP

B_DN

R40

FS7

FS10

FS9

FS5

FS4

FS3

FS6

D19

D18

D21

D20

D16

D17

D15

D14

RL1

RL2

RL3

RL4

NUVL CONTROLLER REV-3.1-1

The Braun Corporation

PWR-IN

1802

R43

R41

U22

102

R38

FS11

GND

12V-B

LIGHT

ALARM

CONTRAST

103

102

V104

L_IN

SW1

SW2

50# CAL

O_BAR

GROUND LVL

R10

C11

R42

The Braun

orporation

U22

102

50# CAL

Button

O_BAR GROUND

LVL Button

Vehicle movement is prevented unless the lift

door is closed, ensuring the lift is stowed.

Lift operation shall be prevented unless the

vehicle is stopped and vehicle movement is

prevented.

The platform will not fold/stow if occupied.

The inner roll stop will not raise if occupied.

The outer barrier will not raise if occupied

The operations listed below must be

functionally veri�ed.

A visual and audible warning will activate if

the threshold area is occupied when the plat-

form is at least one inch below �oor level.

Platform movement is prohibited beyond

the position where the inner roll stop is fully

deployed (up).

Lift platform movement shall be interrupted

unless the outer barrier is deployed (up).

Verify platform lighting when lift is deployed

and pendant illumination when lift is powered.

33675 Rev. A

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun Door 33657 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern