Braun Personal Lift Corporation FMVSS No. 403 Bedienungsanleitung PDF herunterladen (Seite 4)

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32553 Rev. A

JKA

Thresho

Sen

sor Mat

Floor Level and Inner Roll Stop Adjustments

Achieving proper ﬂoor level positioning of the

platform and inner roll stop requires a combina-

tion of Floor Level switch adjustment and inner

roll stop adjustment. Both are factory set but

must be inspected during installation procedures

(will vary per vehicle application).

Ensure the lift is positioned and secured as speci-

ﬁed above (panels 1 and 2). Adjust the Floor

Level switch ﬁrst (detailed below). Then, adjust

the inner roll stop as detailed in the service manual

(adjust only if necessary). The inner roll stop must

rest properly on the vehicle ﬂoor for wheelchair

entry and exit.

Floor Level Switch

The Floor Level switch stops upward travel of

the platform during the Up function (activated

by the torque tube-mounted Floor Level cam).

Position the lift platform 1" above ﬂoor level

using the manual operation system (de-

tailed on opposite side of this sheet). Loosen

the clamp securing the torque tube-mounted

Floor Level cam. Rotate the cam until the

Floor Level switch is activated (cam depresses

switch).

Note: Check the ﬂoor level position of the plat-

form and the inner roll stop after powering the

pump. Hydraulic pressure may affect platform

height slightly. Fine tuning adjustment (tweak-

ing) of the Floor Level switch may be required.

Door Operators/Switch, Terminal

Strip and Floor Level Adjustment

Floor Level Switch

Floor Level Cam

Tor qu e Tu be

Cam depressing switch.

Power Door Operators

Figure O

Black

Jumper

3 4

Terminal Strip

The pump-mounted

terminal strip provides

additional inputs and

outputs that can be

used for optional door

operators, beepers,

interlocks, etc. - as

well as the door safety

switch. The black

jumper wire must be

installed in terminals 6

and 9 to supply power

to the circuit board.

C_SW

O_RL

N/C

IN_LK

12_V

PWR

GND

F_LV

O_SW

C_RL

To Door Openers

“Close” Trigger

To Door Openers

“Open” Trigger

Door Cutout

Orange

Red

Door Cutout

Black

Blue

Install optional

power door oper-

ators as detailed

in the instructions

supplied with

door operator kit.

Route the wires

to the pump mod-

ule and connect

to the terminal

strip as shown in

Figure P.

Figure P

FMVSS 403/404 Certiﬁcation Checklist

Dual

Outer Barrier

Threshold

Area

Platform

Lighting

Visual and Audible

Threshold Warning

Platform

Inner

Roll Stop

DOT — Public Use Lift

Public use vehicle manufacturers

are responsible for complying with

the lift lighting requirements in Fed-

eral Motor Vehicle Safety Standard

No. 404, Platform Lift Installation in

Motor Vehicles (49 CFR 571.404).

Vehicle movement is prevented unless the lift

door is closed, ensuring the lift is stowed.

Lift operation shall be prevented unless the

vehicle is stopped and vehicle movement is

prevented.

The platform will not fold/stow if occupied.

The outer barrier will not raise if occupied.

The inner roll stop will not raise if occupied.

The operations listed below must be

functionally veriﬁed.

Platform movement is prohibited beyond

the position where the inner roll stop is fully

deployed (up).

A visual and audible warning will activate if

the threshold area is occupied when the plat-

form is at least one inch below ﬂoor level.

Lift platform movement shall be interrupted

unless the outer barrier is deployed (up).

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Braun Personal Lift Corporation FMVSS No. 403 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Braun Personal Lift Corporation FMVSS No. 403